Questions? Call 800-508-7110
Genuine Dealer
Auto Parts for Less!
Auto Parts Cheaper - Houston, TX
Orders Over $99.00 Ship Free. 10 Year Warranty Included On All Purchases.
Coupon Codes
 
Find Us on Facebook
Sign Up
Click to verify BBB accreditation and to see a BBB report.Volusion Secure Site

PayPal Logo

 

  2004-2010 Silverado Sierra Revised Canister Vent Valve Kit EVAP Solenoid CVS
2007-2010 Silverado Sierra Revised Canister Vent Valve Kit EVAP Solenoid CVS
 
Additional Photos:




Price: $121.78



Condition: Brand New In Genuine Sealed Packaging.

Orders Over $99 Ship Free!

This Part Features a 10 Year Warranty.


Availability:
In Stock

SKU Number:
19207763
Qty:

Description
 
2004-2010   Chevrolet Silverado

2004-2010   GMC Sierra

Corrects the EVAP vent valve solenoid check engine problem. All you need is this kit and about 10 ft. of 5/8th heater hose and you save yourself the cost of having a mechanic do the same thing for at least twice the cost.

The EVAP canister vent solenoid (CVS) valve draws fresh air into the system through a vent.

Under certain operating conditions, dirt and dust intrusion into the EVAP CVS fresh air intake/venting system, may result in restricted air flow.

Under certain operating conditions, water, if ingested into the EVAP CVS fresh air intake/venting system, may reach the CVS valve causing corrosion in the CVS valve, and may cause restrictions in the fresh air intake path, when the valve is in the closed position.

Installation Instructions:

2004-2007 Model Year (Use Service Kit P/N 19207763)

Raise the vehicle. Suitably support the vehicle.
Disconnect the EVAP canister vent valve electrical connector.
Disconnect the canister pipe from the vent valve.
Push in the retainer and remove the existing canister vent valve from the fuel tank clip or mounting bracket. Discard the old valve.
Cut back the existing canister pipe approximately 51 mm (2 in) to remove the quick connect end.

Install the new canister vent valve solenoid to the fuel tank clip or mounting bracket as shown above. The valve port closest to the electrical connector must point towards the canister.
Cut bulk 5/8" heater hose to a length of approximately 76 mm (3 in). Install the hose between the solenoid and the canister pipe and secure using clamps.
Attach bulk 5/8" heater hose to the vent port and secure using a clamp. Run a length as needed along the frame rail routing to the area above the transmission.
Cut the hose to determined length and install the supplied filter box. Secure using a clamp.
Remove the transmission support and lower the transmission assembly as necessary to allow for access to the new filter box location.


Secure the filter box to the transmission vent hose just forward of the hose tee-section using a tie strap. DO NOT pinch or restrict the transmission vent hose. The filter box opening should be pointing downward.
Raise the transmission and reinstall the transmission support.
Connect the EVAP canister vent valve electrical connector.
Tie strap the hose as needed along the frame rail in order to keep the hose away from pinch-points and heat sources.
Lower the vehicle.

(2007-2010 New Style Models)


After following the published SI diagnostics and determining that the EVAP canister vent valve is the cause of the MIL light, replace the EVAP canister vent valve assembly and relocate the remote filter box. To ensure correct installation, follow the procedures below.

Important: DO NOT replace the EVAP canister assembly for this concern unless it fails the leak test.

Raise the vehicle. Suitably support the vehicle.
Disconnect the EVAP canister vent valve electrical connector.
Disconnect the vent valve pipe quick connect from the canister.
Either cut the existing valve vent pipe and leave the remaining section of pipe in the vehicle or remove along with the valve.
Push in the retainer and remove the existing canister vent valve from the fuel tank clip or mounting bracket.
Cut back the existing canister pipe approximately 51 mm (2 in) and retain the pipe for use with new valve.
Connect the canister pipe quick connect to the canister.


Install the new canister vent valve solenoid to the fuel tank clip or mounting bracket as shown above. The valve port closest to the electrical connector must point towards the canister.
Cut bulk 5/8" heater hose to a length of approximately 76 mm (3 in). Install the hose between the solenoid and the canister pipe and secure using clamps.
Attach bulk 5/8" heater hose to the vent port and secure using a clamp. Run a length as needed along the frame rail routing to the passenger side area above the transmission.
Cut the hose to determined length and install the supplied filter box. Secure using a clamp.
Remove the transmission heat shield, if necessary.
Remove the transmission support and lower the transmission assembly as necessary to allow for access to the new filter box location.


Secure the filter box to the transmission vent hose just forward of the hose tee-section using a tie strap. DO NOT pinch or restrict the transmission vent hose. The filter box opening should be pointing downward.
Raise the transmission and reinstall the transmission support.
Reinstall the transmission heat shield.
Connect the EVAP canister vent valve electrical connector.
Tie strap the hose as needed along the frame rail in order to keep the hose away from pinch-points and heat sources.
Lower the vehicle.

Stock Status: In Stock.

Part Condition:  Brand New.

Part Quality: 100% Genuine (not an aftermarket or a low quality imitation). Includes all the newest Manufacturers Authorized Updates for improved function over the original.

Part Packaging. In Genuine Manufacturers Packaging.

Part Warranty Length: 10 Years.

Ships From: Houston, TX, USA.

Questions? Want to order by phone? Call us 9AM - 5PM  M-F Central Time at 1-800-508-7110
This Part Is Covered By Our Exclusive 10 Year Warranty. If it fails due to manufacturing defects within 10 years of your purchase, we will replace it at no charge to you.



We're Proud To Be 100% USA Owned and Operated. We Are Located In Houston, Texas.


Watch a Short Video About Us and See What We're All About.

 

More About This Part:

  • This Part is a Top of The Line-Premium Grade Auto Part. This is not your average,

Share your knowledge of this product with other customers... Be the first to write a review
(Your shopping cart is empty)
Auto Parts Cheaper is Upfront